Judgment and treatment methods of common faults of electric bicycles
- The power indicator light on the instrument panel does not light up but the motor operates normally.
1. There is no voltage between the positive and negative leads of the dial: the connector is in poor contact or the lead is broken: re-plug or change the wire;
2. The luminous tube is damaged: replace or repair the luminous tube;
3. There is an open circuit on the dial circuit board: Replace or repair the instrument circuit board.
- The motor rotates and stops
1. The battery is low: charge the battery;
2. The battery contacts are in poor contact: adjust the contact position or polish the contacts;
3. There is poor contact between the fuse and the fuse seat in the battery box: adjust or replace it to make it good;
4. There is dirt in the photosensitive tube inside the speed control handle: clean or replace the photosensitive sheet, wipe the photosensitive tube, if the fault still cannot be eliminated: replace the speed control handle;
5. There is a fault in the controller: replace or repair the controller;
6. The lead of the speed control handle seems to be broken: replace or repair the lead;
7. The brake power-off switch is faulty: adjust or replace the brake power-off switch;
8. The power lock has poor contact after ablation: replace or repair the power lock;
9. The connector in the line is virtually connected: re-insert it to make it have good contact;
10. The carbon brushes, wires, and windings in the motor are weakly welded or connected: repair or replace the motor.
- Turn on the power, the controller works normally, turn the handle, but the motor does not rotate.
1. Check whether the speed control cable on the right hand handle has fallen off, and whether the controller or motor connector has fallen off;
2. Check whether the left and right brake handles are powered off.
- Riding is laborious and slow
1. Check whether the brakes are locked;
2. Whether the inner tube air pressure is appropriate;
3. Whether the battery voltage is sufficient;
4. Whether the slope exceeds the limit or is against the wind.
- Short driving distance
1. If the battery is left for a long time: please recharge it first;
2. Whether the tire pressure is insufficient: inflate;
3. Check whether the brakes are too tight and rub against the rim: adjust the brakes;
4. Whether the battery is fully charged: supplementary charging;
5. Whether you encounter uphill slopes or headwinds: pedal-assisted driving;
6. Is the temperature too cold? The battery energy cannot be released.
- Use the key to turn on the power of the electric door lock. The power indicator light on the instrument panel does not light up. If you turn the handle, the motor will not rotate.
1. The fuse on the battery box is burned out: replace the fuse;
2. The fuse on the battery box has poor contact: adjust the fuse tube to make it in good contact;
3. Poor contact on the battery box: adjust the contacts to make good contact;
4. The battery box contacts are burned out: replace them with new ones;
5. The electric door lock is burned out: replace with a new one;
6. The battery lead in the battery box is broken: update the connection line;
7. The battery in the battery box has an internal circuit break: replace or repair the battery;
8. The electric door lock lead or contact lead is broken or has poor contact: rewire.
- When the power switch is turned on, the instrument light is on, but the motor does not rotate when the speed control handle is turned.
1. The controller is damaged: replace or repair the controller;
2. The speed control handle is damaged: Replace or repair the speed control handle;
3. The brake power-off handle is damaged: replace or repair;
4. Internal damage to the motor: replace or repair a new motor;
5. The wire on the car is broken: Reconnect the line.
- Turn on the power and the motor will rotate immediately
1. The speed control handle is damaged: replace or repair;
2. The controller is damaged: replace or repair.
- After charging the battery for 8 hours, the electric car can only run 10 kilometers.
1. Battery aging: replace or repair;
2. The motor is partially short-circuited: replace or repair;
3. The controller is damaged: replace or repair;
4. The charger output voltage is low and the battery is not fully charged: replace or repair the charger.
- The battery cannot be charged or is insufficiently charged.
1. The battery life has expired: replace or repair the battery;
2. The fuse in the battery fuse is broken: replace the fuse;
3. Poor contact between the battery fuse and the fuse seat: adjust the position of the two to make good contact, or replace the fuse;
4. The charger has no output voltage or low output voltage: replace or repair the charger;
5. The charger is in poor contact with the AC 220V power supply: replug the power supply;
6. Abnormal charger indicator light causes false full charge: Replace or repair the charger.




